Sealing Materials Plant
Manufacturer of materials and technologies Abris.
The Abris K material sealing system is used when installing heat-shrinkable sleeves in cable lines with voltages up to 10-35 kV.
The system provides sealing of the cable sheath and joints, interphase filling of couplings, equalization of the electric field strength. This system guarantees protection and reliable operation of the clutch.
Construction diagram
Abris K-EI electrical insulating material in the form of tapes for equalizing the electric field strength in the sleeve
Abris K-MZ is a plastic, gas-tight sealant in the form of prisms for interphase filling of couplings
allows you to displace air from the interphase space, thereby eliminating air ionization and electrical discharges during the operation of the couplings.
Abris K-LB sealing material in the form of tapes to protect cable sheaths
Hard-combustible materials
Abris K, Abris K-LBtg and Abris K-MZpr.tg. in the form of tapes and prisms
Sphere of application:
Main properties of Abris K sealing materials
(Specification: TU 2513-006-52471462-2005)
Indicator name | Brand | |||||
Abris K-EI- 10 | Abris K-EI-15 | Abris K-LB | Abris K-LBtg | Abris K-MZpr. | Abris K-MZ pr.tg | |
1 | 2 | 3 | 4 | |||
Electric strength, kV / mm | 15 | 18 | 18 | |||
Specific volumetric electrical resistance, Ohm x cm | 1010 | 1014 | 1014 | |||
Operating temperature range, ° С | -45…+100 (briefly 120) |
-60…+160 | -60…+160 | |||
The bond strength of the sealant with aluminum when peeling, Н/м, no more | 150 | 150 | 150 | |||
Water absorption, 24h,%, no more | - | 0,2 | 1,0 | 0,2 | 1,0 | |
Oil resistance at 100 ° С, 24h,% no more | 12 | - | - | |||
Relative dielectric permeability at a frequency of 50 Hz, not less | 10 | 15 | - | - | ||
Non-propagation of combustion | - | - | does not support or stops burning | - | does not support or stops burning | |
Resistance to fungi *, points | - | 0-2 | 0-2 |
* The norm for the indicator is provided at the request of the consumer.
Standard sizes of the sealant**, mm |
|||
Abris K-EI-10; Abris K-EI-15 | Abris K-LB; Abris K-LBtg | Abris K-MZ; Abris K-MZ pr. tg | |
Tape | Detail | Tape | Prism |
25*2 | 90*90*4 | 45*2 | 55*18*500 |
120*2 | 90*140*2 | 50*2 | 50*15*600 |
130*2 | 120*150*2 | 25*2 | 55*18*540 |
* * Standard sizes at consumer's request
The main stages of using the Abris K system when assembling a heat-shrinkable sleeve
Stage 1: insulation of the core of the conductor cutting and bolt connectors with Abris K-EI tape to equalize the electric field strength, has oil-resistant properties.
Stage 2: filling the interphase space with Abris K-MZ sealing material to eliminate voids in the interphase space.
Stage 3: insulation of the joints of the grounding conductor and joints of the heat-shrinkable casing with cable insulation to protect the coupling from moisture penetration with the Abris K-LB sealing material.
Section: Tapes
Packing: corrugated cardboard boxes
TU: 2513-006-52471462-2005
Sealant in the form of a self-adhesive tape, which is coated with an anti-adhesive material.
Tapes Packing: corrugated cardboard boxes
TU: 2513-006-52471462-2005
Hard combustible sealant in the form of a self-adhesive tape, which is coated with an anti-adhesive material.
Tapes Packing: corrugated cardboard boxes
TU: 2513-006-52471462-2005
Sealant in the form of a self-adhesive tape, which is coated with an anti-adhesive material.
Packaging: corrugated cardboard boxes
TU: 2513-006-52471462-2005
Sealant in the form of a part (prism), which is coated on both sides with an anti-adhesive coating.
Packaging: corrugated cardboard boxes
TU: 2513-006-52471462-2005
Sealant in the form of a part (hard-burning prism), which is coated on both sides with an anti-adhesion coating.
Ask your question
All fields marked with an asterisk (*) are required