• 01.03.2022

Sealing technology for installation of PVC, aluminium, wood window units

The use of this complex system for the installation of windows, with a slight increase in the cost of these works, will greatly increase the service life of the foam and the thermal insulation indicators of the entire structure as a whole.

Sealing technology for installation of PVC, aluminium, wood window units

The advantages of this type of installation are:

  • meeting all requirements of the state standard;
  • the ability to preserve the upper protective layer of polyurethane foam;
  • low water permeability of the seam;
  • exclusion of exit to the outside and inside of polyurethane foam and the absence of its waste.

Installation of a window block to a wall opening:

  1. breathable tape Abris S-LTdif;
  2. polyurethane foam or other heat insulator;
  3. slope (plaster, gypsum fiber board, plastic);
  4. vapor barrier tape Abris S-LTd;
  5. low tide with sound-absorbing tape Abris S-LTiz;
  6. heat and noise waterproofing tape Abris S-LTiz;
  7. sill.

Stages of work on the installation of a window block in accordance with GOST

Quarter preparation

Stage 1:

Treatment with primer Abris VRP or other primer.  This allows waterproofing and antiseptic treatment of the wall opening, as well as improving the adhesion of vapor barrier tapes.

Stage 2:

Lay the Abris S-LTiz tape along the perimeter of the window opening.  Due to the isolon layer, such a tape, in addition to protecting against dampness and drafts, also provides sound insulation of the window block.

Frame preparation for installation

Stage 3:

Fasten the diffusion (breathable) double-sided tape Abris S-LTdif on three sides (top and sides) of the outer perimeter of the window block, for which it is necessary to remove the protective (anti-adhesive) layer from the edge of the tape that will be attached to the block, and press this edge to  the window block with the sticky side.

Stage 4:

Fix the duplicated tape Abris S-LTd on three sides (top and sides) of the inner perimeter of the window block, for which it is necessary to remove the protective (anti-adhesive) layer from the edge of the tape that will be attached to the block, and press this edge to the window block with the sticky side.

Window frame installation

Stage 5:

Fasten the window block in the window opening, pasted over on three sides with Abris S-LTd tapes (on the outside) and Abris S-LTd (on the inside).

 

 Stage 6:

From the outside, glue the second self-adhesive strip of the tape Abris S-LTdif, for which to remove the protective (anti-adhesive) layer from it and press the tape to the surface of the window opening.

Fastening the window frame to the wall opening, filling the seam

Stage 7:

Fill the pocket formed by the Abris S-LTdif tape with polyurethane foam (from the side of the room).  Tape Abris S-LTdif will protect the polyurethane foam from external UV radiation and moisture, but at the same time will allow it to breathe.

Installation of inner layer sealing materials

Stage 8:

Without waiting for the foam to completely solidify, close it from the side of the room with a duplicated tape Abris S-LTd (it is pasted over the inner sides of the window), for which it is necessary to remove the protective (anti-adhesive) coating from the tape and press the tape to the inner side of the window opening.  The duplicated tape Abris S-LTd will provide additional sealing and waterproofing from the side of the room.

Stage 9:

Close the lower part of the window from the outside with the tape Abris S-LTnp.  The outer surface of this tape is easily primed, painted, plastered, since it is made of non-woven fabric.

Installing low tide

Stage 10:

For additional noise insulation, glue the Abris S-LTiz tape under the external metal drain.

11 Stage:

Install window sills and external drains.

Slope finishing

12 Stage:

perform wet (plaster) or dry (decorative panels) finishing of slopes.

This concludes the technology of performing the vapor barrier of the assembly seam, and the internal finishing work begins.

If you make the installation in this way, the windows will serve for a long time, will reliably protect from frost and dampness.  There will be no drafts or fungus in your home!

Important!:

One of the latest developments of the specialists of the Plant of Sealing Materials LLC are sealants based on natural antiseptics.  Such materials not only do not undergo biological damage, but also cause the death of destructive fungi.


Materials used:

Primer Abris VRP-50

Primer Abris VRP-50

Section: Primers
Packaging: plastic cans
TU: 2316-009-52471462-2007

Sealing tape Abris S-LTiz

Sealing tape Abris S-LTiz

Section: Tapes
Packaging: corrugated cardboard boxes
TU: 5772-003-43008408-99
The sealant is in the form of a self-adhesive tape, which is covered with an anti-adhesive material on the one hand, and reinforced with foamed polyethylene (isolon) of various thicknesses on the other.

Sealing tape Abris S-LTdif

Sealing tape Abris S-LTdif

Section: Tapes
Packaging: corrugated cardboard boxes
TU: 5772-003-43008408-99
A sealant in the form of a self-adhesive tape based on a non-woven fabric with two mounting butyl strips along the edges. On the one hand, the material does not allow moisture to pass through, on the other hand, it helps to filter steam.

Sealing tape Abris S-LTd

Sealing tape Abris S-LTd

Section: Tapes
Packaging: corrugated cardboard boxes
TU: 5772-003-43008408-99
The sealant is in the form of a self-adhesive tape, which is covered with anti-adhesive material on the one hand, reinforced with non-woven fabric on the other, and duplicated with an additional mounting strip.


Ask your question

All fields marked with an asterisk (*) are required

Rambler's Top100 Rambler's Top100 Рейтинг Досок Объявлений Яндекс цитирования